Category Archives: Video

Evolis Dualys 3 Printer – Install a Print Ribbon

A free video demonstrating the method to install a print ribbon in the Evolis Dualys 3 id card printer is available for you. 

 

How to Install a Print Ribbon in the Evolis Dualys 3 ID Card Printer

1. Open the top cover.
2. Place the ribbon in the printer with the supply side to the right.
3. Close the top cover.

Safe-Card ID carries the Evolis Tattoo, Evolis Pebble, Evolis, Dualys, Evolis Quantum and Evolis Securion printers.

Evolis Dualys 2 – Printing a Test Card

SafeCard ID presents a video illustrating how to print a test card using the Evolis Dualys 3 id card printer.

 

How to print a test card.

Safe-Card ID carries the Evolis Tattoo, Evolis Pebble, Evolis, Dualys, Evolis Quantum and Evolis Securion printers.

Evolis Pebble 4 Printer – Install PVC Cards in the Hopper

To learn how to install PVC cards in the hopper of an Evolis Pebble printer, view the following video.

The directions to intstall PVC cards into an Evolis Pebble hopper are as follows:

      1. Take the hopper off of the printer and turn it upside down.

 

      2. Push down the spring tension.

 

      3. Slide the cards into the hopper.

 

      4. Adjust the gauge according to the thickness of the cards used.

 

    5. Reinstall the card hopper.

Safe-Card ID carries the Evolis Tattoo, Evolis Pebble, Evolis, Dualys, Evolis Quantum and Evolis Securion printers.

Evolis Pebble 4 Printer – Cleaning the Printhead

Following is a video demonstrating how to clean the printhead on an Evolis Pebble printer.

 

To clean the printhead, follow the directions displayed in the above video.

      1. Remove the power plug

 

      2. Open the top cover

 

      3. Break the vial in the printhead cleaner and allow the fluid to run to the swab

 

      4. Run the swab across the printhead.

 

      5. Close the top cover

 

      6. Reinstall the power plug

 

    7. Check for power.

Safe-Card ID carries the Evolis Tattoo, Evolis Pebble, Evolis, Dualys, Evolis Quantum and Evolis Securion printers.

Evolis Pebble 4 – Printing a Test Card

Following is a video from www.safecardid.com that illustrates how to print a test card using an Evolis Pebble 4 ID card printer.

 

Directions to Print a Test Card

1. Check to make sure that there is a print ribbon and pvc cards in the printer.

2. Power the printer off.

3. Push the printer power button and turn the power back on. Without releasing pressure, continue holding the power button until the light flashes.

4. As you hold the power button in, the printer will pull a PVC card through the printer and print a test card.

5. Keep the test card in a safe place as it will contain specifications about your printer that may be needed for future parts or repair.

Safe-Card ID carries the Evolis Tattoo, Evolis Pebble, Evolis, Dualys, Evolis Quantum and Evolis Securion printers.

Evolis Dualys – Printing Front and Back Side on One Card

Following is a question and answer from our technical support response team:

Question:

When trying to print front and back of the card on my Evolis Dualys printer, the printer will send 2 separate cards through iand print the front on one card and the back on the other cards instead of printing front and back of the same card. Under printer properties, I do not have access to the back side of the card. I can not figure out if this is a printer or software issue.

Answer:

First, go to the print drivers and make sure that you have a dual sided ribbon selected (YMCKOK). Make sure you have the print driver set to print two sided cards

This should solve the printing error.

For more information about Evolis ID card printers, visit our Evolis Tattoo, Evolis Pebble, Evolis Dualys, Evolis Quantum or Evolis Securion product pages. For a free consultation regarding what printer would be the best fit for your application, contact us toll free at 888-485-4696.

Evolis Pebble 4 – Turning the Power On the Printer

SafeCardID.com offers a free training video which demonstrates how to turn the power on to the Evolis Pebble 4 id card printer.

 

To turn the power on for the Evolis Pebble 4 ID card printer, follow the directions in the video and listed below:

1. Touch the power button the the front of the printer.

2. Wait for the light to light up.

3. The printer will recycle and set the print ribbon for id card printing.

For additional information about Evolis Pebble 4 ID card printers or other Evolis printers, contact us for a free consultation at 888-485-4696.

Asure ID Software – Adding Data and Photos to the Database

SafeCardID.com offers a free training video which demonstrates how to add cardholder data to the database and import pictures from a TWAIN driver camera or computer folder to complete a custom badge ready for printing.

For additional information about Asure ID Card Software, id card printer systems or badge attachments, contact us for a free consultation at 888-485-4696.

Asure ID Card Software – Adding a Bar Code to your Design

SafeCardID.com offers a free training video which demonstrates how to add a bar code field to an id card design designing an id card layout in Asure software programs.

For additional information about Asure ID Express card printing software, ID-card systems, printing supplies or badge attachments and accessories, contact us for a free consultation at 888-485-4696.

[blip.tv ?posts_id=1947539&dest=-1]