Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P120i
Zebra P330i
Zebra P430i

Zebra P330i – Clearing a Card Printer Jam is a post from: SafeCardID.com

Printer Cleaning Instructions:

Clean the printer after 1000 color prints or 5000 monochrome prints. The LCD will display “clean printer” to remind you of this. For best results, clean the printer as soon as possible after this message displays.

1. Leave the printer on and press the button. Hold the button for 3 seconds. The LCD will display “remove ribbon and close head.”
2. Open the printer lid and push the blue release arrow forward. Lift up the printhead carriage..
3. Remove the ribbon spools.
4. Close the head carriage. The LCD with display “empty feeder and press button.”
5. Open the feeder lid and remove all cards but the bottom card. This card will remain in the feeder until you press the eject button.
6. Load the cleaning card in the feader. Place the small cleaning card in the card feeder. The belt will move it in halfway and continue to clean other parts of the printer. The small card will be ejected when it has finished cleaning.
7. The LCD will display “press button to continue.” Feed the long cleaning card into the card feeder exit slot. It will move back and forth as it cleans. The LCD will display “cleaning printer.”
8. When completed, the LCD screen will display “ready.” You may return the ribbon spools, reload cards and resume printing.

If you notice spots or streaks, you may need to clean the printhead.

1. Turn the printer off.
2. Lift the carriage and remove the print ribbon.
3. Sqeeze the plastic cleaning swab stick to move the liquid into the tip.
4. Move the moistened swab side to side across the elements. Wait 2 minutes.
5. Turn the printer back on and return the print ribbon.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P120i

Zebra P330i
Zebra P430i

Zebra P330i – Routine Printer Cleaning Recommendations is a post from: SafeCardID.com

To add the 220 card extended card feeder to the Zebra P330i printer, follow the directions provided in the video.

1. Remove the feeder cover by pressing in on the left side and pivoting out the right corner.
2. Place the feeder extension on top of the printer case and align the holes.
3. Insert screws into the three holes and tighten slightly.
4. Place the bottom corner of the feeder onto the small raised pivot point. Place the top pivot point into the hole in the feeder extension.
5. Completely tighten the screws.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P120i

Zebra P330i
Zebra P430i

Zebra P330i – Installing an Extended Card Feeder is a post from: SafeCardID.com

ID Card Printing Tips for The Zebra P330i Card Printer

1. Install the print driver.
2. Load the print ribbon, cleaning cartridge and the cards.
3. Plug in the correct power cord for your location.
4. Connect the USB cable to the printer and computer.
5. Turn on the printer.
6. The LCD will display “initallizing” and then “ready”.
7. Teh computer will recognize the printer.
8. Slide out the output hopper.
9. Begin printing.
8. The LCD will display the action of the computer during printing.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P120i

Zebra P330i
Zebra P430i

For other Zebra printing tips see the following videos:

Zebra P330i – Using the Single Card Feeder>br/>
Zebra P330i – Installing A Print Ribbon

Zebra P330i – Loading PVC Cards

Zebra P330i – Installing Printer Drivers

Zebra P330i – Installation Tips

Zebra P330i – ID Card Printing Tips is a post from: SafeCardID.com

To set up the Zebra P330i printer for feeding single cards, follow the steps listed in the video.

First, the driver setting must be changed.
1. Empty the card feeder by removing the cards.

2. Use the eject command to remove the remaining id card in the printer.

a. Open the printer properties menu.
b. Select the device settings tab.
c. Go to the tools menu.
d. There are two eject card buttons to select from:

i. A button to eject the cards from the print engine.
ii. A button to eject the cards from the feeder and the print engine.

Second, insert the card into the slot under the feeder lid on the right side of the printer.

Third, the card will automatically be drawn into the printer with the print job is sent.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i

For other Zebra printing tips see the following videos:

Zebra P330i – ID Card Printing Tips

Zebra P330i – Installing A Print Ribbon

Zebra P330i – Loading PVC Cards

Zebra P330i – Installing Printer Drivers

Zebra P330i – Installation Tips

Zebra P330i – Using the Single Card Feeder is a post from: SafeCardID.com

Following are the directions to install a printer ribbon in the Zebra P330i printer:

1. Make sure that you will be installing a True Colors i series ribbon and it is recommended to leave the printer on during the printer ribbon installation.

2. Open the printer lid and push the blue release arrow forward.

3. Lift up the printhead carriage and remove the used ribbon.

4. Hold the ribbon spool in your right hand with the white end facing the printer. In your left hand, hold the empty spool. The tape should still be attached.

5. Make sure the ribbon feeds across the top of the spools.

6. Place the ribbon on the spindle located under the printhead carriage. Place the empty spool on the take up spindle to the left of the carriage.

7. Press the spools firmly onto the spindles.

8. Press down on the printhead carriage until it clicks into position.

9. The printer will automatically adjust the ribbon. If the ribbon was installed correctly the LCD display will display the word “ready”.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i
Zebra P520i

For other Zebra printing tips see the following videos:

Zebra P330i – ID Card Printing Tips

Zebra P330i – Using the Single Card Feeder

Zebra P330i – Loading PVC Cards

Zebra P330i – Installing Printer Drivers

Zebra P330i – Installation Tips

Zebra P330i – Installing a Print Ribbon is a post from: SafeCardID.com

The printer driver for the Zebra P330i can be installing using the following steps:

1. Insert the Windows CD into the computer CD-Rom Drive. The Install Wizard will guide our installation on the computer.
2. After selecting “install print driver” from the main menu, the install shield wizard will install on the computer.
3. Click next to continue.
4. The select the features window will display. Select the install USB printers drivers button.
5. The license agreement will display. Click yes to continue installation.
6. The setup type window will display. Select the appropriate installation and click next.
7. The select program screen will display. Choose the default or folder of your choice.
8. The setup status window will display the progress of the installation.
9. The congratulations window will display. Click next.
10. You will have an option to read the read me files.
11. The install wizard complete screen will display. Click finish to restart the computer.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i

For other Zebra printing tips see the following videos:

Zebra P330i – ID Card Printing Tips

Zebra P330i – Using the Single Card Feeder

Zebra P330i – Installing A Print Ribbon

Zebra P330i – Loading PVC Cards

Zebra P330i – Installation Tips

Zebra P330i – Installing ID Card Printer Drivers is a post from: SafeCardID.com

To load PVC cards into a Zebra P330i printer:

1. Open the lid card feeder locared on the right hand side of the printer.
2. Verify the card thickness guage is set up properly for your card thickness.
3. Open the cards. Remove the PVC cards from their wrapper and shuffle carefully while holding the sides of the cards.
4. Place the cards into the feeder. The top cards will lie at an angle.
5. Close the feeder lid.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i
Zebra P520i

Zebra P330i – Loading PVC Cards is a post from: SafeCardID.com

When opening the Zebra P330i printer for the first time, you will find the following tips helpful:

1. Remove both of the reusable handles on the sides of the box.
2. Slide the top of the box up.
3. In the top tray of the styrofoam packing, you will find the following:

• Driver
• Cleaning Supplies
• Quick Start Quide
• Documentation CD
• USB Cable
• Power Supply
• Cleaning Cartridge Assemby

4. Remove the top styrofoam piece.
5. Remove the yellow tape.
6. Push the blue release forward.
7. Lift up the printhead carriage.
8. Remove the printhead protector.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i

For other Zebra printing tips see the following videos:

Zebra P330i – ID Card Printing Tips

Zebra P330i – Using the Single Card Feeder

Zebra P330i – Installing A Print Ribbon

Zebra P330i – Loading PVC Cards

Zebra P330i – Installing Printer Drivers

Zebra P330i – Installation Tips is a post from: SafeCardID.com

It is recommended to not force a card jammed into the machine out, but to eject it automatically using the computer interface and the following steps.

1. Click on the computer start button.
2. Click on settings.
3. Open the printers directory.
4. Select the P120i printer and right click to open properties.
5. Select the device settings.
6. Select the tools menu.
7. Select properties.
8. Click on the eject card button on the bottom right hand corner of the screen.
9. The card will eject from the front of the printer.

Find out specific information about Zebra Printer models:

Zebra P110i
Zebra P330i
Zebra P430i
Zebra P520i

Zebra P120i – Clearing a Card Jam is a post from: SafeCardID.com