SafeCardID.com

ID Works Software – How to Add Fields to a Production Template

SafeCard ID Team — Fri, 27 Jan 2012 15:54:21 +0000

Need to know how to add text fields and other fields to your card template in ID Works card printing software? Check out this video for step by step instructions.

Our ID card experts at Safe-Card ID can assist you with your ID card printer, ID card software and any supplies needed to complete your ID cards. Contact us toll free at 888-485-4696.

ID Works Software – How to Add Fields to a Production Template is a post from: SafeCardID.com

ID Works Software – How to Design a Card Template

SafeCard ID Team — Wed, 25 Jan 2012 15:50:00 +0000

Datacard has released the following training video to teach users how to create a basic design template in their ID card software, ID Works.

Our ID card experts at Safe-Card ID are available to recommend the best ID card printer, card printing software and supplies for your application. Contact them toll free at 888-485-4696.

ID Works Software – How to Design a Card Template is a post from: SafeCardID.com

Persona C30e – How to Calibrate the Ribbon

SafeCard ID Team — Wed, 04 May 2011 15:37:16 +0000

To calibrate the ribbon sensor, click the Start button in the lower left corner of your monitor and select Settings. Then select Printers and Faxes. Depending on your installation of Windows, you may need to go to the Control panels and then select Printers.

In the Printers and Faxes window, Right Click on the driver for your printer and select Printing Preferences from the list.

In the Persona C30e Card Printer Printing Preferences window, Select the Calibrate tab and then click the Sensors button.

For the C30 and C30e printers follow the instructions in the Calibration window to calibrate the ribbon sensor. When the calibration is complete, the printer will beep twice.

Note that for the C30 or C30e printer, you must cover the front of the printer before clicking the send button to prevent ambient light from entering the printer as it may negatively impact the ribbon calibration process.

For information about Fargo printers or other photo id card systems, contact our ID card experts at 888-485-4696.

Persona C30e – How to Calibrate the Ribbon is a post from: SafeCardID.com

Evolis Pebble 4 – All the Lights are On

SafeCard ID Team — Sun, 01 May 2011 14:48:11 +0000

If you are trying to print your custom printed cards on your Evolis Pebble and find you can’t, adjustments are needed to continue printing. If you notice that all of the lights on the printer are lit, follow the steps below to see if the problem can be fixed.

1. Check to see which ribbon is in the printer. Make sure it is a 5 panel YMCKO color ribbon
2. Go to the print queue and clear it out. Once you have cleared the print que out, restart the printer so it starts fresh
3. Open and close the print head. Make sure that the color ribbon is in the correct place upon closure.
4. Check their printer graphics settings. Make sure that the correct ribbon is selected.
5. Once you have done all this, try to print again.

If the steps above turn off the extra lights that are on, you should be able to continue printing. If the problem is not fixed, additional steps are needed to reset the printer. The best thing to do is contact the ID card integrator company that provided you with the printer for technical assistance.

Evolis printers purchased at Safe-Card ID come with free phone technical support for the lifetime of the printer. If you need personalized assistance with your printer, please contact us our technical area with your invoice number and printer serial number. We will be happy to assist you.

Our ID card experts can provide you the latest information about ID card printers, ID card software and PVC cards. Contact them toll free at 888-485-4696.

Evolis Pebble 4 – All the Lights are On is a post from: SafeCardID.com

Persona C30e – Wrong Ribbon Error

SafeCard ID Team — Thu, 28 Apr 2011 15:53:32 +0000

If you have a wrong ribbon error with your Fargo or Persona C30 or C30e printer, the following procedure can be used adjust the printer driver settings to correct the error.

To correct the wrong ribbon error, on the Printers and Faxes page, right click on the C30 or C30e printer and choose Printing Preferences.

In the Printing Preferences window, choose the Device Options tab.

From within the Device Options tab, select the correct ribbon type. Alternatively, you can select the ribbon type by clicking the Auto Ribbon Select button. After selecting the correct ribbon type, click the OK button. Then stop/close the program from which you are printing and then restart it so that it will recognize the corrected ribbon setting.

If you are not sure of your ribbon type, check the part number on the box the ribbon came in.

For information about Fargo printers or other photo id card systems, contact our ID card experts at 888-485-4696.

Persona C30e – Wrong Ribbon Error is a post from: SafeCardID.com

Barcode Printing Inconsistently with a Fargo DTC550

SafeCard ID Team — Tue, 26 Apr 2011 16:33:02 +0000

If your printing with a Fargo DTC500 printer and your bar code printing is not consistent, you may need to follow this tip:

The light printing of the black in the barcodes is caused by the angle of the printhead being to small. Note that the barcode darkens to normal as the print approaches the center of the card. Increasing the printthead angle will darken the beginning of the barcode. After adjusting the angle of the printhead it may be necessary to raise the Ribbon Peel-Off Bar.

Please consult with the ID card intergrator technical support area where you purchased your printer to obtain assistance for your specific printer issue prior to adjustment. For information about the Fargo DTC550 and current Fargo printers, contact our ID Card experts at 888-485-4696.

Barcode Printing Inconsistently with a Fargo DTC550 is a post from: SafeCardID.com

Fargo DTC500 With a Ribbon Peel Off Bar Line

SafeCard ID Team — Fri, 22 Apr 2011 17:50:07 +0000

Our Fargo technical representatives are sharing some common issues with ID card printing. If the following picture looks like the card printing problem you are having, the ribbon peel off bar may need adjustment.

The dark area at the beginning of the card is caused by the “Ribbon Peel-Off Bar” being adjusted too low. When the printhead starts printing the printhead pressure is normal until the card goes under Ribbon Peel-Off Bar. The remainder of the card is printed too light because the Ribbon Peel-Off Bar lifts the printhead slightly off of the card.

To correct this problem it is necessary to raise the Ribbon Peel Off Bar slightly.

Fargo DTC500 With a Ribbon Peel Off Bar Line is a post from: SafeCardID.com

Fargo DTC500 Prints A Light Bar Code

SafeCard ID Team — Mon, 18 Apr 2011 16:55:46 +0000

Printing ID cards sometimes is difficult as the exact card specifications are critical to the success of the identification program. One important printing requirement is a correct, dark version of the provided bar code. If your bar code is not meeting your requirements, check out the pictures below and see if your problem is displayed. If so, we have recommendations for you.

The light printing of the black in the center barcode is caused by the Ribbon Peel-Off Bar being adjusted too low. Note the horizontal streaking in the bars. Note also that the effect is across the full length of the card. (The light/dark banding on the upper and lower barcodes is due to “camera effect” and not to a problem with the printer)

To correct this problem it is necessary to raise the Ribbon Peel-Off Bar slightly.

The light printing of the black in the barcodes is caused by the angle of the printhead being to small. Note that the barcode darkens to normal as the print approaches the center of the card. Increasing the printhead angle will darken the beginning of the barcode. After adjusting the angle of the printhead it may be necessary to raise the Ribbon Peel-Off Bar.

To correct this problem increase the printhead angle by completing the printhead angle adjustment.

Please consult with the ID card intergrator technical support area where you purchased your printer to obtain assistance for your specific printer issue prior to adjustment. For information about the Fargo printers and current Fargo printer models, contact our ID Card experts at 888-485-4696.

Fargo DTC500 Prints A Light Bar Code is a post from: SafeCardID.com

Fargo DTC550 Printer Prints ID Cards with Smudges

SafeCard ID Team — Thu, 14 Apr 2011 16:44:39 +0000

When an ID card is printed, sometimes it enters the output hopper with smudges appearing to be fingerprints. If you are wondering what to do, the following may provide the answer for you.

If your card looks like this:

You need to know that the white smudge marks are caused by contamination on the card surface which prevents the color from adhering to the card surface.

The problem can be the result of fingerprints on the cards. Always handle cards by the edges. If the problem persists on a number of cards, replace the card stock with a clean group of cards.

If your card looks like this:

The dark smudges are caused by fingerprints on the ribbon prior to printing the card.

This problem can normally be solved by careful handling of the ribbon during removal/replacement. Always handle ribbon by the spindles. This problem will usually disappear after printing a couple of cards.

Additional Fargo technical tips provided by Fargo authorized technical representatives are available through this blog. If you need additional assistance with Fargo printer information, please contact our ID card specialists toll free at 888-485-4696.

Fargo DTC550 Printer Prints ID Cards with Smudges is a post from: SafeCardID.com

Fargo DTC550 Printer Prints ID Cards with Pink Streaks

SafeCard ID Team — Mon, 11 Apr 2011 17:34:28 +0000

The pink lines on this card are caused by the Ribbon Peel-Off Bar being too high on the lower edge of the card (side towards the front of the printer).

The pink lines on this card are caused by the Ribbon Peel-Off Bar being too high on the upper edge of the card (side towards the rear of the printer).

The pink lines on this card are caused by the Ribbon Peel-Off Bar being too high on both edges of the card.

To correct this problem, it is best to consult with the technical support staff from the integrator who sold you the printer. They may recommend that you lower the end of the Ribbon Peel-Off Bar that towards the back of the printer. A very small adjustment is required.

For additional information about Fargo printer models, contact our ID card experts at 888-485-4696.

Fargo DTC550 Printer Prints ID Cards with Pink Streaks is a post from: SafeCardID.com